- 您现在的位置：买卖IC网 > Sheet目录878 > RVB0G151MNG (Nichicon)CAP ALUM 150UF 4V 20% SMD
Precautions
General Precautions at Designing, for Use and Handling
1. Circuit design precautions
(1) Check the rated performance
After checking the operation and installation environments, design the circuit so that it falls within the rated performance range
stipulated in the catalog specification.
(2) Operating temperature and ripple current
a) Set the operating temperature so that it falls within the range stipulated in the catalog specification.
b) Do not apply current that exceeds the allowable ripple current in the catalog.
(3) Leakage current
Even when the soldering conditions fall within the range of the catalog specification, the leakage current increases slightly.
It also increases slightly during high temperature no-load, moisture-proof no-load and temperature cycling tests with
no voltage applied.
In cases such as these, leakage current will decrease by applying voltage in conditions below the maximum operating temperature.
(4) Applied voltage Considerations
a) Make sure the sum of the peak DC voltage and ripple voltage values does not exceed the rated voltage.
b) Please do not apply the reverse voltage to FPCAP .
c) When the DC voltage is low, please check whether the peak value of ripple voltage does not become a reverse voltage.
(5) Reduction of failure stress
The main failure mode of the FPCAP is in the open mode primarily caused by an electrostatic capacitance drop.
Random short circuit mode failures occur rarely.
The time it takes to reach the failure mode can be extended by using the FPCAP with reduced ambient temperature,
ripple current and applied voltage.
(6) Capacitor insulation
a) Insulation is not guaranteed.
b) Be sure to completely separate the case, negative electrode terminal and positive electrode terminal from adjacent components
and PC board traces.
(7) Operating environment
Do not use the FPCAP in the following environments.
a) Places where it can come into direct contact with water or salt water and places where condensation may form.
b) Places filled with noxious gasses such as: hydrogen sulfide, sulfurous acid, nitrous acid, chlorine, ammonia, etc.
c) Places exposed to ozone, ultraviolet rays and radiation.
d) Where severe vibration or shock which exceeds the condition specified in the specification sheets.
(8) Assembly Conditions Considerations
In designing a circuit, the following conditions should be checked before the FPCAP is mounted on the PC board.
a) The pitch and diameter of PCB holes to which the FPCAP is mounted, shall be designed in conformance with the dimensional
tolerance stipulated in the catalog specifications.
(9) PC board
Avoid locating heat-generating components around the FPCAP and on the underside of the PC board under the FPCAP .
(10) Parallel connection
When used in a parallel connection with another capacitor, carefully select the type of capacitor.
(11) Other
a) Electrical characteristics are affected by fluctuations in temperature and frequency.
b) When mounting the FPCAP on a double-sided PC board, design the board so that extra PC board holes are not located
underneath the FPCAP .
2
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
RW-4815D
CONV DC/DC 3W 36-72VIN +/-15VOUT
RW-483.3S/SMD
CONV DC/DC 3W 36-72VIN 3.3VOUT
RW2-483.3D/H3/SMD
CONV DC/DC 2W 36-72VIN +/-3.3V
RY-0505D
CONV DC/DC 1W DL +/-5V OUT SIP7
RZ-2415S-R
CONV DC/DC 0.5W 24VIN 15VOUT
S1008R-393K
INDUCTOR SHIELDED 39UH SMD
S100J25U2MU6BK0R
CAP CER 10PF 6KV 5% RADIAL
S102M43Z5P283L6R
CAP CER 1000PF 1.5KV 20% RADIAL
相关代理商/技术参数
RVB0G221MNG
功能描述:铝质电解电容器-SMD 4.0V 220uF TOL 20%
RoHS:否 制造商:Nichicon 电容:220 uF 容差:20 % 电压额定值:4 V ESR:15 mOhms 工作温度范围:- 55 C to + 105 C 尺寸:4.3 mm W x 7.3 mm L x 2.8 mm H 产品:Low ESR Electrolytic Capacitors
RVB0J101MNG
功能描述:铝有机聚合物电容器 100 UF 6.3V 20%
RoHS:否 制造商:Panasonic Electronic Components 电容:470 uF 容差:20 % 电压额定值:2.5 V ESR:4.5 mOhms 工作温度范围:- 40 C to + 105 C 端接类型:SMD/SMT 外壳直径: 外壳长度:7.3 mm 外壳宽度:4.3 mm 外壳高度:1.9 mm 封装:Reel
RVB0J151MNG
功能描述:铝质电解电容器-SMD 6.3V 150uF TOL 20%
RoHS:否 制造商:Nichicon 电容:150 uF 容差:20 % 电压额定值:6.3 V ESR:20 mOhms 工作温度范围:- 55 C to + 105 C 尺寸:4.3 mm W x 7.3 mm L x 2.8 mm H 产品:Low ESR Electrolytic Capacitors
RVB1C270MNG
功能描述:27μF 16V Aluminum - Polymer Capacitors 2917 (7343 Metric) 30 mOhm 1000 Hrs @ 105°C 制造商:nichicon 系列:FPCAP，VB 包装:剪切带（CT） 零件状态:过期 电容:27μF 容差:±20% 额定电压:16V ESR（等效串联电阻）:30 毫欧 不同温度时的使用寿命:105°C 时为 1000 小时 工作温度:-55°C ~ 105°C 极化:极化 应用:通用 纹波电流:1.4A 阻抗:- 引线间距:- 大小/尺寸:0.287" 长 x 0.169" 宽（7.30mm x 4.30mm） 高度 - 安装（最大值）:0.118"（3.00mm） 表面贴装焊盘尺寸:- 安装类型:表面贴装 封装/外壳:2917（7343 公制） 标准包装:1
RVB1C330MNG
功能描述:33μF 16V Aluminum - Polymer Capacitors 2917 (7343 Metric) 30 mOhm 1000 Hrs @ 105°C 制造商:nichicon 系列:FPCAP，VB 包装:剪切带（CT） 零件状态:过期 电容:33μF 容差:±20% 额定电压:16V ESR（等效串联电阻）:30 毫欧 不同温度时的使用寿命:105°C 时为 1000 小时 工作温度:-55°C ~ 105°C 极化:极化 应用:通用 纹波电流:1.4A 阻抗:- 引线间距:- 大小/尺寸:0.287" 长 x 0.169" 宽（7.30mm x 4.30mm） 高度 - 安装（最大值）:0.118"（3.00mm） 表面贴装焊盘尺寸:- 安装类型:表面贴装 封装/外壳:2917（7343 公制） 标准包装:1
RVB1C470MNG
功能描述:47μF 16V Aluminum - Polymer Capacitors 2917 (7343 Metric) 30 mOhm 1000 Hrs @ 105°C 制造商:nichicon 系列:FPCAP，VB 包装:剪切带（CT） 零件状态:过期 电容:47μF 容差:±20% 额定电压:16V ESR（等效串联电阻）:30 毫欧 不同温度时的使用寿命:105°C 时为 1000 小时 工作温度:-55°C ~ 105°C 极化:极化 应用:通用 纹波电流:1.4A 阻抗:- 引线间距:- 大小/尺寸:0.287" 长 x 0.169" 宽（7.30mm x 4.30mm） 高度 - 安装（最大值）:0.118"（3.00mm） 表面贴装焊盘尺寸:- 安装类型:表面贴装 封装/外壳:2917（7343 公制） 标准包装:1
RVB1E150MNG
功能描述:15μF 25V Aluminum - Polymer Capacitors 2917 (7343 Metric) 30 mOhm 1000 Hrs @ 105°C 制造商:nichicon 系列:FPCAP，VB 包装:剪切带（CT） 零件状态:过期 电容:15μF 容差:±20% 额定电压:25V ESR（等效串联电阻）:30 毫欧 不同温度时的使用寿命:105°C 时为 1000 小时 工作温度:-55°C ~ 105°C 极化:极化 应用:通用 纹波电流:1.4A 阻抗:- 引线间距:- 大小/尺寸:0.287" 长 x 0.169" 宽（7.30mm x 4.30mm） 高度 - 安装（最大值）:0.118"（3.00mm） 表面贴装焊盘尺寸:- 安装类型:表面贴装 封装/外壳:2917（7343 公制） 标准包装:1
RVB1E270MNG
功能描述:27μF 25V Aluminum - Polymer Capacitors 2917 (7343 Metric) 30 mOhm 1000 Hrs @ 105°C 制造商:nichicon 系列:FPCAP，VB 包装:剪切带（CT） 零件状态:过期 电容:27μF 容差:±20% 额定电压:25V ESR（等效串联电阻）:30 毫欧 不同温度时的使用寿命:105°C 时为 1000 小时 工作温度:-55°C ~ 105°C 极化:极化 应用:通用 纹波电流:1.4A 阻抗:- 引线间距:- 大小/尺寸:0.287" 长 x 0.169" 宽（7.30mm x 4.30mm） 高度 - 安装（最大值）:0.118"（3.00mm） 表面贴装焊盘尺寸:- 安装类型:表面贴装 封装/外壳:2917（7343 公制） 标准包装:1